UniData Communication Systems WPU-7700 Specifications

WPU-7700 Enterprise Edition Administrator Manual UniData Communication Systems Inc.

9 BASIC USAGE Names and functions of the KEY Key Name Icon Basic functions Direction key ▲▼◄► Used for menu viewing, Can be pres

10 Get to Administrator Menu and Change Password Then, push the left direction key to go to the settings mode. Select the Admin Menu to enter 1 Pr

11 5 Enter Password

12 NETWORK Connect to new Temporary profile It is only for the temporarily connected profile. The existing temporary profile will be disappeared if y

13 Make New Network Profile WPU-7700 supports 4 profiles to provide a function of connecting WPU-7700 to various wireless LAN environments. Based

14 Modify Network Profile WPU-7700 supports feature to modify saved profiles. 1 Press the AP search key to enter WLAN search mode in Standby mod

15 Delete Network Profile WPU-7700 supports feature to delect saved profiles. In WLAN search mode, select Menu then 4.Delete to remove WiFi Network

16 Change Priority Network Profile The higher position profile in the screen has higher priority to connect automatically 1 Press the AP search key

17 Security While set the profile up, security option can be set. Select setup for security using the direction key ▲▼◄► , and confirm using the O

18 Certification manager In case of EAP-TLS, Select “Certs manger” in administrator menu. You can see the message below if you select “View Root CA”

1 UniData Communication Systems is registered trademarks of UniData Communication Systems Inc. Other referenced trademarks are trademarks (registere

19 TCP/IP . WPU-7700 support DHCP and manual IP. Select “DHCP” or ”Manual IP” using the direction key ▲▼◄► in network setup screen, and confirm

20 VoIP SIP In System mode, Select “VoIP setting” Using the ( - ) key. After choosing the VoiP setting, enter display name, User name, Auth User nam

21 4 Put 1st_Proxy and 2nd_Proxy. 1st_proxy: SIP 1st proxy 2nd_proxy: SIP 2nd proxy QoS Qos: Quality of Service 1 Select “8.QoS” in System mode

22 3 Enter Signal DSCP and Voice DSCP. Coder WPU-7700 supports G.711-ALaw-64K, G.729, G729 codec. 1 Select “9. Coder” in System mode 2 Select “Cod

23 4 Select “Menu” in Voip mode to set the priority. Set the priority order of audio coder.

24 SIP Outbound Proxy 1 Select “10. SIP Outb Proxy” in System mode. 2 Select “Voip” in SIP Outb Proxy mode 3 Put the SIP Outbound Proxy.

25 DIAGNOSTIC Diagnose Network Select “Diagnostic” in System mode. Diagnose Network, WLAN and RTP. Results of Diagnose Network In NetDiag, i

26 2. TCP/IP status (Connection of TCP/IP) GW: connection to Gateway WAN: connection to WAN 3. Result to PER (Packet Error Rate) PER to GW: packe

27 Diagnose WLAN WLAN and search available Access Point. It will be searching the unit of the Access Point and the unit of the Channel‘s Access Poin

28 RSSI: Received Signal Strength Indication (dBm) SNR: Signal to Noise Ratio (dBm) NF: Noise Floor (dBm) RP: Rx Packet Count/Rx Bytes TP: Tx Packet

2 Manual Introduction Before use, kindly read this “Administrator Manual” thoroughly to have an understanding of the contents After reading, place

29 Diagnose RTP Present-displayed screen show that the phone is disconnected. Present-displayed screen show that the phone is connected. Oral inp

30 Diagnosis by checking RTP -Connect phone from P1 to P2. -Having a Hold in P1. -In P1, Press on the Hidden key before pressing on SEND. -Diagnosis

31 LCD/LED test 1 Select “5.LCD/LED TEST” in Diagnostic mode. 2 Diagnose the LCD and LED of the phone. . Speaker TEST 1 Select “6. Speaker TEST”

32 Ping test 1 Select “2. Ping test” in System mode. Ping Test is accessible for simple diagnosis of network. 2 Select “1.Gateway, DNS server, AP

33 Manual Input

34 AUTOPROVISINING GUIDE WPU-7700 supports autoprovisioning to configure and to update firmware. General Sequence of Autoprovisioning ① Get IP from

35 Setting Auto provisioning Server Address There are two way to set Auto provisioning Server address. The first one is input address in menu via th

36 Setting the .ini file in Autoprovisioning Server Users use the value of two Entry after modifying according to each condition. Make sure that seve

37 [MWI] Use_MWI = 1 / min: 0(not use), max : 1 (use): Message waiting indication Use_Subscribe = 1 / min: 0(not use), max : 1 (use): Message subscr

38 Gateway = 0.0.0.0 / IP Address Format DNS1 = 0.0.0.0 / IP Address Format DNS2 = 0.0.0.0 / IP Address Format Security = 2 / min :0, max : 5 Securit

3 Since this is provided to make safe and right use of WPU-7700 to prevent any accidents or risks, be sure to carefully read it, follow instructions,

39 [NETWORK2~4] Reference Network 1 [PROVISION] Firmware_Version = 02.01.00 / min: 0, max :30 chars Firmware_Name = wpu7700-common-20081031-02-01-00

40 FirmWare upgrade There are two way to set Firm ware update. The first one is input address in menu via the key pad; another one is upgraded by Au

4 Be careful for conductors such as necklaces, keys, and coins not to contact battery terminals (metal section). Since short circuits can cause exp

5 Correctly install WPU-7700 in compliance with instructions. Otherwise, it can cause an abnormal operation of WPU-7700, or reduce their life. Be

6 If batteries are not used for a long time, keep them at room temperature after charging. If you want to use again after leaving them for a long

7 INDEX BASIC USAGE .........

8 General Sequence of Autoprovisioning ..................... 34 Setting Auto provisioni